What Redmond, WA rainfall means for your gutters
At about 37.8 inches a year, a 5-inch K-style gutter is the standard specification and handles typical rainfall comfortably. Downspout placement matters more than gutter size at this rainfall.
| Annual rainfall | 37.8 inches |
|---|---|
| Recommended gutter | 5-inch K-style |
| Downspout every | 40 feet of run |
| Typical single-storey home | 4 downspouts |
| Installed cost, seamless aluminium | $5–$12 per linear foot |
| Typical 160-foot job | $800–$1,925 |
Climate figures are NOAA 1991–2020 normals from Seattle Sand Pt WFO, 6 miles away. Cost figures are typical local ranges, not a quote.
Ice and freeze risk in Redmond, WA
January lows average 37°F, so freezing happens but rarely persists.
Occasional overnight freezes are enough to split a gutter seam that is already holding standing water, which is an argument for correct pitch rather than for cold-weather hardware.
When to clear gutters in Redmond, WA
With 37.8 inches of rain a year and a distinct wet season, two clear-outs a year suits this climate — spring and again before October.
Nothing freezes here, so timing follows the rain rather than the calendar. Clearing before the wet season is what prevents overflow down the fascia — the damage in a no-freeze climate is rot, not ice.
Seamless gutter cost in Redmond, WA
Installed seamless aluminium runs $5–$12 per linear foot in Redmond, putting a typical 160-foot single-storey job at $800–$1,925. Rural rates run below the national average, though travel charges can offset that on longer call-outs.
The 5-inch profile recommended for this rainfall carries a higher material cost per foot than the smaller section, which is already reflected above. Roof height, fascia condition and the number of corners move the final figure more than the gutter itself does.
Gutter questions specific to Redmond, WA
What size gutters do I need in Redmond, WA?
At about 37.8 inches a year, a 5-inch K-style gutter is the standard specification and handles typical rainfall comfortably. Downspout placement matters more than gutter size at this rainfall. For a typical single-storey roof here, plan on about 4 downspouts, one roughly every 40 feet of run.
How much do seamless gutters cost in Redmond, WA?
Installed seamless aluminium generally runs $5–$12 per linear foot locally, so a typical 160-foot single-storey job lands around $800–$1,925. Rural rates run below the national average, though travel charges can offset that on longer call-outs. These are typical ranges rather than a quote — the price turns on roof height, fascia condition and how many corners the run has.
How often should gutters be cleaned in Redmond, WA?
Twice a year suits this climate, given roughly 37.8 inches of annual rain. Nothing freezes here, so timing follows the rain rather than the calendar. Clearing before the wet season is what prevents overflow down the fascia — the damage in a no-freeze climate is rot, not ice.
Do I need to worry about ice dams in Redmond, WA?
January lows average 37°F, so freezing happens but rarely persists. Occasional overnight freezes are enough to split a gutter seam that is already holding standing water, which is an argument for correct pitch rather than for cold-weather hardware.
When is the best time to have gutters installed in Redmond, WA?
Aim for spring and again before October. Seamless gutter is formed on site from a coil machine, and hanging it is easier and the sealant cures better above freezing, so late autumn work gets progressively harder to schedule as temperatures drop.
Are seamless gutters worth it compared with sectional?
Sectional gutter leaks at the joints, and every joint is a future failure point. Seamless runs are rolled to length on site so the only joints are at corners and outlets. With 37.8 inches of rain a year, fewer joints mainly means fewer places for the sealant to fail under sustained wetting.
What month should I book gutter cleaning in Redmond, WA?
September is the month to aim for — November is the wettest month of the year here at 5.9 inches, and clearing debris before that is worth more than clearing it after. Rain is spread across roughly 7 months here, so a single annual visit tends not to be enough — split it either side of the wettest stretch.
When is the quietest time of year for gutters in Redmond, WA?
July is the driest month locally. With no month averaging a freezing low, that is simply the best window to book installation or repair without working around weather.
My Redmond home is fairly new — do I still need to think about gutters?
27% of housing in Redmond, WA was built after 2010 (US Census ACS), so most homes here are still on their original hidden-hanger systems and the fascia is usually sound. At that age the work is normally replacement by choice — upsizing to handle 37.8 inches of annual rain, or changing material — rather than repair after a failure.
Does this apply if I live in an apartment or condo in Redmond?
Only partly. Just 36.3% of units in Redmond, WA are single-family detached (US Census ACS), so a large share of buildings here have gutters that are a building-wide responsibility rather than an individual owner's. On multi-unit buildings the run is longer, access often needs lift equipment priced separately, and the decision usually sits with an association or landlord.
Month-by-month gutter calendar for Redmond, WA
November is the wettest month in Redmond, WA at 5.9 inches, and July the driest. Rain is spread across 7 months of the year, so there is no single quiet season — inspection matters more here than one annual clean-out. No month averages a freezing low, so ice dams are not a design concern here.
| Month | Rain | High | Low | Gutter load | What to do |
|---|---|---|---|---|---|
| January | 5.1" | 47°F | 37°F | Peak | Heaviest flow of the year — confirm downspouts discharge away from the foundation |
| February | 3.5" | 50°F | 37°F | High | Inspect after heavy rain for overflow at corners and seams |
| March | 3.9" | 54°F | 39°F | High | Inspect after heavy rain for overflow at corners and seams |
| April | 3" | 59°F | 43°F | Moderate | Routine check of hangers, seals and slope |
| May | 2.2" | 65°F | 48°F | Moderate | Routine check of hangers, seals and slope |
| June | 1.6" | 70°F | 53°F | Low | Routine check of hangers, seals and slope |
| July | 0.8" | 77°F | 57°F | Low | Quietest month — best window for installation or repair |
| August | 1" | 77°F | 57°F | Low | Routine check of hangers, seals and slope |
| September | 1.7" | 71°F | 53°F | Low | Clear debris now, before the wet season starts |
| October | 3.7" | 61°F | 47°F | High | Inspect after heavy rain for overflow at corners and seams |
| November | 5.9" | 52°F | 41°F | Peak | Heaviest flow of the year — confirm downspouts discharge away from the foundation |
| December | 5.6" | 47°F | 37°F | Peak | Heaviest flow of the year — confirm downspouts discharge away from the foundation |
Monthly normals are NOAA 1991–2020 from SEATTLE SAND PT WFO, 7 miles away. Gutter load is scored against this city's own wettest month, not a national average.
Redmond, WA homes and what that means for gutter work
| Housing units | 35,104 |
|---|---|
| Built before 1960 | 2.5% |
| Built since 2010 | 27% |
| Single-family detached | 36.3% |
| Owner occupied | 43.2% |
| Median home value | $1,167,800 |
27% of the housing stock went up after 2010, so most runs are still on their original hidden hangers and the work is more often replacement by choice than by failure.
Only 36.3% of units here are single-family detached. On multi-unit buildings gutter work is usually a building-wide decision rather than a homeowner's, and access often needs lift equipment that is priced separately.
With 43.2% owner occupancy, a large share of properties are landlord-decided, where gutter work tends to follow a leak rather than a schedule.
Housing figures are US Census Bureau ACS 2024 5-year estimates.
Redmond gutter cost calculator
Adjust the run length, material and storey count for your own property. Figures are adjusted for Redmond labour rates and the 5-inch profile this city's rainfall calls for.
Gutter cost estimator for Redmond, WA
Typical installed ranges. Not a quote — the final figure depends on fascia condition, access and how many corners the run has.
A typical single-storey home runs 150–200 ft.
Estimated total
$1,200–$2,600
About $8–$16 per linear foot installed
| Line item | Estimate |
|---|---|
| Aluminium gutter, 160 ft | $875–$1,875 |
| 4 downspouts | $200–$425 |
| Remove and dispose of existing gutter | $150–$300 |
| Total | $1,200–$2,600 |
Gutter work available in Redmond, WA
Installers in the Redmond network cover seamless installation formed on site, repairs to leaks, sagging and storm damage, and full replacement. The 5-inch profile and 4 downspouts set out above is what a quote here should be based on. See what each service involves.
Signs You Need Seamless Gutter Repair or Installation
- Frequent clogging
- Visible cracks or splits
- Gaps between gutters and fascia boards
- Water pooling around your foundation
- Rust spots or peeling paint on your gutters
Which gutter material suits Redmond, WA
Neither ice nor volume forces the choice here
At 37.8 inches of annual rain neither ice nor volume is the limiting factor, so material is mostly a budget and appearance decision. Standard .027 aluminium is adequate and is what most local quotes assume.
The failure mode to watch in a dry climate is UV on the finish and sealant at the corners and outlets, not corrosion — expect to re-seal joints sooner than a wetter climate would need.
Copper costs several times aluminium and is chosen for appearance and lifespan rather than performance. It needs compatible fasteners and hangers throughout — copper in contact with steel or aluminium corrodes galvanically, which is the most common way an expensive copper run fails early.